May 27, 2020· The crushing value of an aggregate indicates its resistance against crushing under gradually applied compressive loads. The standard aggregate crushing test is made on aggregate passing 12.5mm IS sieve and retained on 10 mm IS sieve. Procedure. About 6.5 Kg material consisting of aggregates passing 12.5mm IS sieve and retained on 10mm sieve is ...
The apparatus used for determining aggregate impact value of coarse aggregates is Impact testing machine conforming to IS: 2386 (Part IV)- 1963,IS Sieves of sizes – 12.5mm, 10mm and 2.36mm, A cylindrical metal measure of 75mm dia. and 50mm depth, A tamping rod of 10mm circular cross section and 230mm length, rounded at one end and Oven.
The Procedure of Impact Test on Aggregates: The following procedure is applied, to find out the impact value of aggregate: Aggregates for the test sample can be decided by passing it through 12.5 mm sieve and retained on 10 mm sieve.
Jan 04, 2014· Procedure of testing Aggregate Crushing Value (ACV): 1. Make a sieve analysis and get sufficient amount of aggregate by using 14.0 mm passing sieve and 10.00 mm retained sieve. 2. After sieving fill the cylinder in thre layers by the aggregate and apply 25 blows by the tamping rod with a approximate height of 50 mm. 3.
The bulk density and void percentage of aggregate can be evaluated using standard test methods of applicable codes such as ASTM C 29/C29M-17a, IS: 2386 (Part 3) – 1963, or BS 812-2:1995. The procedure provided in this article is based on the specification of ASTM standard ( ASTM C 29/C29M-17a). The bulk density or unit [.]
Aggregate crushing value test on coarse aggregates gives a relative measure of the resistance of an aggregate crushing under gradually applied compressive load. Coarse aggregate crushing value is the percentage by weight of the crushed material obtained when test aggregates are subjected to a specified load under standardized conditions.
Read More: AGGREGATE CRUSHING VALUE TEST – PROCEDURE AND RESULT. Objective: This method of test used to measure the impact value of aggregate use in the construction of Highway pavement and concrete structure. Reference:-IS 2386 (Part 4) – 1963. Apparatus:-
Apr 28, 2016· Aggregate Crushing Value and Its Test Procedure: One of the test in which concrete material can fail is due to crushing under compressive stress. Aggregate crushing test is standardized by IS: 2386 part-IV and used to verify the crushing strength of aggregates. The aggregates should be oven dried, which can passes through 12.5mm and retained on ...
about 3 kg) are required for each test (wet and dry). SECTION 3. PROCEDURE 3.1 Dry test a) Place the crushing cylinder on its base plate, and add a test spesimen in thirds, tamping each layer with 25 light strokes of the tamping rod. Level the surface of the aggregate and insert the plunger (taking care to ensure that it does not jam in the ...
The strength of coarse aggregates is assessed by aggregates crushing test. The aggregate crushing value provides a relative measure of resistance to crushing under a gradually applied compressive load. To achieve a high quality of pavement, aggregate possessing low aggregate crushing value .
aggregate to crushing under a gradually applied compressive load. Crushing value is a measure of the strength of the aggregate. The aggregates should therefore have minimum crushing value. 3. APPARATUS The apparatus of the aggregate crushing value test .
Now, the final report of aggregate impact value is calculated as, Final report of aggregate impact value test. Weight of oven dried aggregate sample (A) = 332.8 gm. Weight of fraction (dust) of aggregate passing through 2.36 mm sieve (B) = 23.2 gm. Aggregate impact value,
Figure 7.7.1 Outline form of cylinder and plunger apparatus for the aggregate crushing value and ten percent fines test e) A ventilated oven, thermostatically controlled at a temperature of 1050C plus or minus 50C. f) A rubber mallet, a metal tray of known mass and large enough to contain 3 kg of aggregate and a brush with stiff bristles.
Batch mixer to mix the bitumen and aggregates; Test procedure. Take the dried aggregate of 200g and place in the 20mm sieve. Now shake the sieve and collect the retained aggregate from 12.5mm sieve. Then take the bitumen binder at 5 % of the aggregate weight. Now heat the collected aggregates at 150°C and heat the bitumen binder at 160°C.
Calculate Aggregate Crushing Value. The ratio of the weight of fines formed to the total sample weight in each test shall be expressed as a percentage, the result being recorded to the first decimal place: Aggregate Crushing Value = W B W A × 100. Where, W A is weight of surface-dry sample
Test Method: IS: 2386 (P-1) 1963. Impact Value: This test helps in determining the value which indicates the ability of an aggregate to resist crushing. The lower the figure the stronger the aggregate, i.e. the greater its ability to resist crushing. Test Method: IS: 2386 (P .
PROCEDURES FOR AGGREGATE INSPECTION 2019 Construction Field Services Division Aggregate Quality Unit . i ... aggregate testing for state or federally funded projects require Michigan Certified Aggregate Technician (MCAT) training at the level appropriate for .
Sampling for Aggregate Crushing Value Test: For the Aggregate crushing value test, an aggregate sample passing through 12.5 mm IS sieve and retained on 10mm IS sieve is selected and dried to a temperature of 105 ºC to 110 ºC then cooled to room temperature. To fill the cylindrical measure mould about 6.5 kg of a sample of aggregate is sufficient.
This test is repeated once or twice and the average crushing value of the aggregate is determined. The average crushing value in the different tests is the actual crushing value of aggregate. Important points to remember. It is recommended that the crushing value of aggregate should be less than 30%.
7.6.6 Aggregate impact value 7.6.6.1 Procedure a) Test specimens in a dry condition (i) Fix the cup firmly in position on the base of the impact machine and place the whole of the specimen in it and then compact by 25 strokes of the tamping rod. Adjust the height of .
The Aggregate Crushing Value (ACV) Test Set provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Each set consists of steel cylinder, plunger, base plate, cylindrical measure and tamping rod. All parts of the apparatus are powder coated or galvanized steel, heat treated and ground ...
The procedure of aggregate crushing value test aggregate crushing value mould. take the empty weight of cylindrical measure as w1. fill aggregate sample passing through 12.5 mm and retained on 10 mm is sieve in measuring cylinder in 3 equal layers such that .
May 08, 2013· Objective For determination of the aggregate crushing value of coarse aggregate, which passes 12.5 mm. IS sieve and retained on 10 mm. IS sieve. Reference Standard IS: 2386 (Part IV)-1963 Methods of test for aggregate for concrete Part IV Mechanical Properties. Equipment & Apparatus Steel Cylinder Sieves (12.5mm,10mm) Cylindrical metal measure Tamping Rod Balance (0 .
2.1 Object - This method of test covers the procedure for determining aggregate crushing value of coarse aggregate. NOTE 1 -The 'aggregate crushing value' gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggre- gate of 'aggregate crushing value' 30 or higher, the ...
